Horizon drilling rig 33

Deepwater Horizon was an ultra-deepwater, , owned by and operated by the company. On 20 April 2010, while drilling in the at the , a caused an explosion on the rig that killed 11 crewmen and ignited a fireball visible from 40 miles (64 km) away. The fire was inextinguish. [pdf]

FAQS about Horizon drilling rig 33

How many rigs does horizon have?

Since then, our fleet has grown to where it is today with 34 rigs, making Horizon the fourth largest drilling contractor in Canada. Our mission is to provide our clients with the best possible experience as we continue to build our extensive fleet of innovative products and purpose-built rigs.

What oil rigs did Deepwater Horizon work on?

Deepwater Horizon worked on wells in the Atlantis (BP 56%, BHP 44%) and Thunder Horse (BP 75%, ExxonMobil 25%) oil fields. It was described at times as a "lucky" and "celebrated" rig, and in 2007 was still described as "one of the most powerful rigs in the world".

What makes our 34 rigs a top-notch rig?

Our 34 rigs remain top-notch due to our innovative approach to our ever-growing fleet. With versatile equipment to meet your needs, some of our rigs include features such as AC power, top drive, dual fuel, automated catwalk, iron roughneck, hydraulic substructure levelling, and hydraulic BOP handling.

How deep is the Tiber Oil Field?

In 2006, it discovered oil in the Kaskida oil field and, in 2009, the "giant" Tiber oil field. The well in the Tiber field had a true vertical depth of 35,050 ft (10,683 m) and a measured depth of 35,055 ft (10,685 m), below 4,132 ft (1,259 m) of water.

Who died in the Deepwater Horizon rig fire?

An eleventh worker also died in the subsequent fire, a crane operator: Aaron Dale Burkeen, 37, Philadelphia, Mississippi. 115 workers survived. The rig was evacuated, with injured workers airlifted to medical facilities. After approximately 36 hours, Deepwater Horizon sank on 22 April 2010.

What equipment do you need for a rig?

With versatile equipment to meet your needs, some of our rigs include features such as AC power, top drive, dual fuel, automated catwalk, iron roughneck, hydraulic substructure levelling, and hydraulic BOP handling. Our equipment gives us an edge over the competition.

Moonpool drilling rig

A moon pool is an equipment deployment and retrieval feature used by , , , , and or , and. . The Hughes was a 50,500 long tons (51,300 t), 619-foot-long (189 m) ship constructed by the United States in the early 1970s for the from the Pacific seabed. The desig. . Very deep moon pools are used in —submerged chambers used by divers engaged in underwater research, , , and . In this case, shown in part D of. . Moon pools are becoming increasingly used on to allow for hauling of the gear in worse weather conditions. They also reduce the exposure of fish to air, improving quality. Along with bird scarin. [pdf]

Elevator drilling rig

Drill pipe elevators for USC with taper shoulder and square shoulder weld-on tool joints shall have bore dimensions as specified in Table 1. Notes on Table 1: Oilfield elevators with identical bores are the same. 1. * Not Manufactured. 2. ** Obsolescent connection. 1. 1 Dimension DTE from API Spec. 7, Table 4.2 2. 2. . A very close fit of the hinge pin and pawl significantly affects the correct functioning of an elevator – especially the center-latch elevator. If there is play in the hinge, the elevator tends to. . In addition to the side-door elevator, single-joint and slip-type casings are used in running casing. We use a single-joint elevator (Figure 7) to. . Since both care and inspection procedures depend primarily upon the amount of service the equipment has had, it is challenging to project. . The following checks apply to all types of elevators. For a quick reference to critical points of the drill pipe elevators, see Figure 29. 1. Is the oilfield elevator size correct? 2. Are the dies of slip-type elevators sharp? 3. Are the hinge pin or holes worn? 4. Are. [pdf]