RAISING THE LEGENDARY DRILL
Raising procedure for ideco hfr 142 1000 drilling rig
Raise the bottom of the mast to the rig floor and pin it in place. Raise the crown section into place on the derrick stand. Raise the "A-legs" and pin them into place. Pin the monkeyboard in place on the mast. Lay out all lines and cables to prevent tangling when the mast is raised. [pdf]FAQS about Raising procedure for ideco hfr 142 1000 drilling rig
How much does an Ideco 1000 hp rig cost?
IDECO 1000 HP DRILLING RIG (Ref#9965Tb) Manufactured 2004, 117’ SHL telescoping mast, mounted on 3 axle, 358,000# static hook load, 5-sheave travel block, racking board, mounted on 3 axle trailer, optional 250 ton top drive/power swivel Price as is: $700,000 Price reworked cleaned, painted and certified: $1,300,000
How much does an Ideco H44 drill rig cost?
IDECO H44 DRILL RIG (Ref#3977T) 1000 hp trailer mounted drill rig, (2) Detroit 60 Series engines 475 hp each @ 1800 rpm, 117’ x 450,000# derrick, 17’ adjustable substructure, Century 17-1/2” x 44” rotary tble, National 160 ton Shorty block, V door catwalk, water tank/doghouse combo Price: $275,000
How should a rig rig be secured before raising a mast?
Be sure the derrick escape device is in place and the line is properly secured to the mast before raising the mast. All rig floor winch lines, tong hanger lines, etc., should be secure to prevent them from getting tangled with the blocks as the mast is raised.
How much does a Ideco H37 rig cost?
IDECO H37 WELL SERVICE RIG (Ref#1683RR) 103' x 244,000# franks telescoping hydraulically raised mast, Detroit Series 60 diesel engine, Allison 5860 transmission, mounted on 5 axle carrier, hyd leveling jacks, hyd utility hoist, air and hyd controls, front flotation tires Price: $245,000
How much does a 1000 hp drill rig cost?
IDECO 1000HP DRILLING RIG (Ref#11167N) Single drum drawworks, 1-1/8" drilling line, hydramatic brake, 2 engine compound (2) Detroit Series 60 diesel engine 550 hp each (drives rig and carrier), 112' x 378,000# mast, 8 lines, 16' substructure, mounted on 6 axle carrier, (2) 6061 Allison transmission, No additional equipment Price: $825,000
How much does a dreco H44 rig cost?
IDECO H44 DRILL RIG (Ref#3981T) Drive in, rated to 6500’ with 4-1/2” drill pipe, (2) Detroit 871 engines (305 hp each), Ideco 108’ x 268,000# mast, 12’ H telescoping substructure, Dreco 150 ton block, ZP 17-1/2” x 44” rotary table, V-door catwalk, water tank/doghouse combo Price: $215,000
Parts of drill rig
Drilling derricks and Rig Masts consist of a steel framework with a square or rectangular cross-section. Their purpose is to support the hoisting equipment and rack the tubulars while tripping pipe. The number of joints in a stand (single-double-triple) that the rig can pull is dependent on the height of the derrick. . The Drawworks is one of the most important components of the drilling rig (types of drilling rigs). The unit supplies the hoisting power, the. . The Crown Blockas a drilling rig component is a fixed set of pulleys (called sheaves) located at the top of the derrick or mast, where the drilling line is threaded. The companion blocks to these pulleys are the traveling blocks. By using two sets of blocks in this fashion,. . The Traveling Blockis a set of sheaves (pulleys) that move up and down in the derrick. The drilling line is threaded (reeved) over the. . Attached to the bottom of the traveling blocks, the hook is required to hang the swivel and rig kelly(for drilling) and the elevator bales (for tripping pipe and casing). . • (#22) is a section of large diameter pipe fitted to the top of the that the attaches to via a side outlet, to allow the to flow back to the .• (BOPs) (#23 and #24) are devices installed at the wellhead to prevent fluids and gases from unintentionally escaping from the . #23 is the annular (often referred to as Hydril named after a manufacturer), and #24 is the pipe rams and blind rams. [pdf]FAQS about Parts of drill rig
What are the components of a drilling rig?
1. Mast or Derrick Usually the first component of the drilling rig people notice, the mast is a tall fabricated structure towering above all the other drilling components. The mast is vitally important, as it supports the components of the drilling mechanism hovering above the point where drilling will take place.
How many systems are there on a drilling rig?
There are 4 main systems on a drilling rig: Ac-Dc Power Generation Station Example: Drilling derricks and Rig Masts consist of a steel framework with a square or rectangular cross-section. Their purpose is to support the hoisting equipment and rack the tubulars while tripping pipe.
How does a drilling rig work?
The drilling line spools out under gravity and is reeled in by an electrical or diesel engine. The Crown Block as a drilling rig component is a fixed set of pulleys (called sheaves) located at the top of the derrick or mast, where the drilling line is threaded. The companion blocks to these pulleys are the traveling blocks.
What is a drilling rig mast?
Usually the first component of the drilling rig people notice, the mast is a tall fabricated structure towering above all the other drilling components. The mast is vitally important, as it supports the components of the drilling mechanism hovering above the point where drilling will take place. 2. Drilling Line
What is an offshore drilling rig?
Offshore drilling rigs have similar elements, but are configured with a number of different drilling systems to suit drilling in the marine environment. The equipment associated with a rig is to some extent dependent on the type of rig but typically includes at least some of the items listed below.
How many brake systems does a drill rig have?
On most rigs, there are at least two brake systems. stop. a loaded traveling block, but is not capable of bringing it to a complete stop. An integral part of the drawworks is the gear system. This gives the driller a wide choice of speeds for hoisting the drillstring. two catheads.
