Raising procedure for ideco hfr 142 1000 drilling rig

Raise the bottom of the mast to the rig floor and pin it in place. Raise the crown section into place on the derrick stand. Raise the "A-legs" and pin them into place. Pin the monkeyboard in place on the mast. Lay out all lines and cables to prevent tangling when the mast is raised. [pdf]

FAQS about Raising procedure for ideco hfr 142 1000 drilling rig

How much does an Ideco 1000 hp rig cost?

IDECO 1000 HP DRILLING RIG (Ref#9965Tb) Manufactured 2004, 117’ SHL telescoping mast, mounted on 3 axle, 358,000# static hook load, 5-sheave travel block, racking board, mounted on 3 axle trailer, optional 250 ton top drive/power swivel Price as is: $700,000 Price reworked cleaned, painted and certified: $1,300,000

How much does an Ideco H44 drill rig cost?

IDECO H44 DRILL RIG (Ref#3977T) 1000 hp trailer mounted drill rig, (2) Detroit 60 Series engines 475 hp each @ 1800 rpm, 117’ x 450,000# derrick, 17’ adjustable substructure, Century 17-1/2” x 44” rotary tble, National 160 ton Shorty block, V door catwalk, water tank/doghouse combo Price: $275,000

How should a rig rig be secured before raising a mast?

Be sure the derrick escape device is in place and the line is properly secured to the mast before raising the mast. All rig floor winch lines, tong hanger lines, etc., should be secure to prevent them from getting tangled with the blocks as the mast is raised.

How much does a Ideco H37 rig cost?

IDECO H37 WELL SERVICE RIG (Ref#1683RR) 103' x 244,000# franks telescoping hydraulically raised mast, Detroit Series 60 diesel engine, Allison 5860 transmission, mounted on 5 axle carrier, hyd leveling jacks, hyd utility hoist, air and hyd controls, front flotation tires Price: $245,000

How much does a 1000 hp drill rig cost?

IDECO 1000HP DRILLING RIG (Ref#11167N) Single drum drawworks, 1-1/8" drilling line, hydramatic brake, 2 engine compound (2) Detroit Series 60 diesel engine 550 hp each (drives rig and carrier), 112' x 378,000# mast, 8 lines, 16' substructure, mounted on 6 axle carrier, (2) 6061 Allison transmission, No additional equipment Price: $825,000

How much does a dreco H44 rig cost?

IDECO H44 DRILL RIG (Ref#3981T) Drive in, rated to 6500’ with 4-1/2” drill pipe, (2) Detroit 871 engines (305 hp each), Ideco 108’ x 268,000# mast, 12’ H telescoping substructure, Dreco 150 ton block, ZP 17-1/2” x 44” rotary table, V-door catwalk, water tank/doghouse combo Price: $215,000

Drill rig manual pdf

Drilling derricks and Rig Masts consist of a steel framework with a square or rectangular cross-section. Their purpose is to support the hoisting equipment and rack the tubulars while tripping pipe. The numbe. [pdf]

How to remove the large gear of the rock drill

Rocks are infamously durable and can be an eyesore in a garden, in a landscaping project or it may just be in the way. The problem usually is that the rock is too heavily embedded or it's simply too heavy to lift or roll out of the way. By breaking a rock you can. [pdf]

FAQS about How to remove the large gear of the rock drill

What tools do you need to remove a rock?

Here is Rock Busters’ step-by-step guide on how to handle rock removal safely and effectively. Depending on the rock’s size, you may need some or all of these tools: Rotary Hammer Drill: To make holes in the rock. Feathers and Wedges: These fit into drilled holes to create cracks. Sledgehammer: For driving wedges and breaking off pieces.

How do you drill a hole in a rock?

Using a rotary hammer drill, create several holes in the rock’s surface. Drill as deep as the wedges require and clear out any dust to help the wedges grip. Spacing the holes evenly around the rock will help you get cleaner breaks. Now, insert a wedge between two feathers in each hole, making sure the feathers face outward.

How do you drill a boulder?

With a shovel, dig away all the dirt around the boulder the expose its general shape and size. Drill several 1⁄2 inch (1.3 cm) diameter holes into the surface of the rock and remove dust. While wearing goggles, drill a series of evenly spaced holes across the surface of the rock.

How do you remove a rock if you break it?

By breaking a rock you can decrease the load and remove it in a safer manner. Place the rock onto a flat surface, if possible. If you can manage to move the rock, try and move it so that it's in on a flat surface where it has little chance of moving once you hit it a few times.

How do you break a rock with a rotary hammer?

Exposing as much of the rock as possible will make it easier to break. Using a rotary hammer drill, create several holes in the rock’s surface. Drill as deep as the wedges require and clear out any dust to help the wedges grip. Spacing the holes evenly around the rock will help you get cleaner breaks.

How do you remove dust from a rock?

Drill several 1⁄2 inch (1.3 cm) diameter holes into the surface of the rock and remove dust. While wearing goggles, drill a series of evenly spaced holes across the surface of the rock. Then, use a bulb-type syringe to remove the excess dust within the small holes.